Storage Controllers
Software RAID
HPE Smart Array S100i SR Gen10 SW RAID
NOTE: All models come with the S100i Smart Array Controller with embedded software RAID support for up to 12 bays. The S100i uses 14 embedded SATA ports, but only 12 are available for bays as 2 are leveraged to support the M.2 connectors on the optional SATA M.2 capable primary riser (867978-B21).
NOTE: HPE Smart Array S100i SR Gen10 SW RAID will operate in UEFI mode only. For legacy support an additional controller will be needed, and for CTO orders please also select the Legacy mode settings part, 758959-B22.
NOTE: HPE Smart Array S100i SR Gen10 SW RAID is off by default and must be enabled.
NOTE: The S100i supports windows only.
NOTE: For Linux users, HPE offers a solution that uses in-distro open-source software to create a two-disk RAID 1 boot volume. For more information visit: https://downloads.linux.hpe.com/SDR/project/lsrrb/
|
|
Essential RAID Controllers
· HPE Smart Array E208i-a SR Gen10 Controller
· HPE Smart Array E208i-a SR G10 LH Controller
· HPE Smart Array E208i-p SR Gen10 Controller
· HPE Smart Array E208e-p SR Gen10 Controller
Performance RAID Controllers
· HPE Smart Array P408i-a SR Gen10 Controller
· HPE Smart Array P408i-a SR G10 LH Controller
· HPE Smart Array P408i-p SR Gen10 Controller
· HPE Smart Array P408e-p SR Gen10 Controller
· HPE Smart Array P816i-a SR Gen10 Controller
· HPE Smart Array P816i-a SR G10 LH Controller
NOTE: If GPGPU is needed then the LH controller (low profile heatsink) should be ordered to allow GPU to fit in the chassis.
NOTE: For additional details, please see HPE Smart Array Gen10 Controllers Data Sheet.
|
|
Maximum Storage
|
Storage
|
Capacity
|
Configuration
|
Hot Plug SFF SAS HDD
|
26.4 TB
|
8+2+1 x 2.4 TB (with optional UMB + rear drive option)
|
Hot Plug SFF SATA HDD
|
22 TB
|
8+2+1 x 2.0 TB (with optional UMB + rear drive option)
|
Hot Plug SFF SAS SSD
|
168.3 TB
|
8+2+1 x 15.3 TB (with optional UMB + rear drive option)
|
Hot Plug SFF SATA SSD
|
84.48 TB
|
8+2+1 x 7.68 TB (with optional UMB + rear drive option)
|
Hot Plug SFF NVMe PCIe SSD
|
153.6 TB
|
10 x 15.36 TB NVMe
|
Hot Plug LFF SAS HDD
|
64 TB
|
4 x 16 TB
|
Hot Plug LFF SATA HDD
|
64 TB
|
4 x 16 TB
|
Hot Plug LFF SAS SSD
|
7.68 TB
|
4 x 1.92 TB
|
Hot Plug LFF SATA SSD
|
7.68 TB
|
4 x 1.92 TB
|
|
|
Graphics
· Integrated video standard
· Video modes up to 1920 x 1200 @ 60 Hz (32 bpp)
· 16 MB Video Memory
· HPE iLO 5 on system management memory
· 32 MB Flash
· 4 Gbit DDR3 with ECC protection
|
|
Power Supply
· HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit
NOTE: Available in 94% efficiency.
· HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit
NOTE: Available in 94% and 96% efficiency.
NOTE: Also available in -48VDC and 227VAC/380VDC power inputs.
· HPE 1600W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit
NOTE: Available in 94% efficiency.
NOTE: 1600W Power supplies only support high line voltage (200 VAC to 240 VAC).
HPE Flexible Slot (Flex Slot) Power Supplies share a common electrical and physical design that allows for hot plug, tool-less installation into HPE ProLiant Gen10 Performance Servers. Flex Slot power supplies are certified for high-efficiency operation and offer multiple power output options, allowing users to "right-size" a power supply for specific server configurations. This flexibility helps to reduce power waste, lower overall energy costs, and avoid "trapped" power capacity in the data center.
All pre-configured servers ship with a standard 6-foot IEC C-13/C-14 jumper cord (A0K02A). This jumper cord is also included with each standard AC power supply option kit. If a different power cord is required, please check the ProLiant Power Cables web page.
To review the power requirements for your selected system, please use the HPE Power Advisor Tool.
For information on power specifications and technical content visit HPE Server power supplies.
|
|
Operating Systems and Virtualization Software
2nd Generation Intel® Xeon® Scalable Processor Family
· Windows Server 2019: Essentials, Standard, Datacenter
· Windows Server 2016: Essentials, Standard, Datacenter
· Windows Server 2012 R2: Essentials, Standard, Datacenter
· Microsoft Hyper-V Server: 2012 R2, 2016 & 2019
· VMware vSphere: 6.0 U3, 6.5 U2 & 6.7 U1
NOTE: 6.5 U3, 6.7 U3 & 7.0 minimums for "R", 6250 & 6256 processors.
· ClearVM: 7.6 & 8.0
· Red Hat Enterprise Linux (RHEL): 7.6 w/ Kbase **, 7.7, 8.0, and 8.1
· SUSE Linux Enterprise Server (SLES): 12 SP3 & SP4, 15 and 15 SP1 (includes Xen) **
1st Generation Intel® Xeon® Scalable Processor Family
· Windows Server 2019: Essentials, Standard & Datacenter
· Windows Server 2016 : Essentials, Standard & Datacenter
· Windows Server 2012 R2: Essentials, Standard & Datacenter
· Microsoft Hyper-V Server: 2012 R2, 2016 & 2019
· VMware vSphere: 6.0 U3, 6.5 & 6.7
· ClearVM: 2.0
· Red Hat Enterprise Linux (RHEL): 6.9 & 7.3**
· SUSE Linux Enterprise Server (SLES): 11 SP4, 12 SP2 & 15 (includes Xen) **
NOTE: **64-bit only;includes KVM
· ClearOS
NOTE: ClearOS allows you to build a fully functional server that is just right for you at no upfront cost. For more information on ClearOS, please visit http://www.hpe.com/servers/clearos.
· CentOS
NOTE: For more information on Hewlett Packard Enterprise Certified and Supported ProLiant Servers for OS and Virtualization Software and latest listing of software drivers available for your server.
http://www.hpe.com/info/ossupport
|
|
HPE Server UEFI/Legacy ROM
Unified Extensible Firmware Interface (UEFI) is an industry standard that provides better manageability and more secured configuration than the legacy ROM while interacting with your server at boot time. HPE ProLiant Gen10 servers have a UEFI Class 2 implementation and support both UEFI Mode (default) and Legacy BIOS Mode.
NOTE: The UEFI System Utilities tool is analogous to the HPE ROM-Based Setup Utility (RBSU) of legacy BIOS. For more information, please visit http://www.hpe.com/servers/uefi.
|
Interfaces
Serial
|
1 port - Optional
|
Video
|
1 Front - Display port (optional 8 SFF and 4 LFF only)
1 Rear - VGA port (standard on all chassis types)
NOTE: Both ports are not active simultaneously.
|
Network Ports
|
4x 1GbE embedded NIC (if equipped/depending on model)
|
1 FlexibleLOM slot available on all chassis types (supporting various NICs adapters)
|
iLO Remote Mgmt Port
|
1 Gb Dedicated
|
MicroSD Slot
|
1 MicroSD slot
NOTE: The MicroSD slot is not hot-pluggable, server must be powered down before removal.
|
USB 3.0
|
Up to 5 total: 1 front, 2 rear, 2 internal (standard on all chassis types)
+1 optional USB 2.0 front (on 8 SFF and 4 LFF only)
|
SID (Systems Insight Display)
|
Optional for all chassis types
NOTE: Will lose iLO Service Port if selecting this option.
|
|
|
Industry Standard Compliance
· ACPI 6.1 Compliant
· PCIe 3.0 Compliant
· WOL Support
· Microsoft® Logo certifications
· PXE Support
· USB 3.0 Compliant
· USB 2.0 Compliant (only on optional Universal Media Bay)
· SMBIOS 3.1
· UEFI 2.6 (Unified Extensible Firmware Interface Forum)
· Redfish API
· IPMI 2.0
· Secure Digital 4.0
· TPM 1.2 and 2.0 support
· Advanced Encryption Standard (AES)
· Triple Data Encryption Standard (3DES)
· SNMP v3
· TLS 1.2
· DMTF Systems Management Architecture for Server Hardware Command Line (SMASH CLP)
· Active Directory v1.0
· ASHRAE A3/A4
· Energy Star
· European Union (EU) eco-design regulations for server and storage products, known as Lot 9, go into effect on March 1st, 2020. Among other requirements, for servers this directive establishes power thresholds for idle state, as well as efficiency and performance in active state which vary among configurations. HPE ProLiant Gen10 servers are compliant with Lot 9 requirements. For more information regarding HPE Lot 9 conformance, please visit:
https://www.hpe.com/us/en/about/environment/msds-specs-more.html
NOTE: For additional technical thermal details regarding ambient temperatures, humidity and features support please visit: http://www.hpe.com/servers/ashrae.
|
|
UEFI
Configure and boot your servers securely with industry standard Unified Extensible Firmware Interface (UEFI).
Learn more at http://www.hpe.com/servers/uefi.
|
|
Embedded Management
HPE Integrated Lights-Out (HPE iLO)
Monitor your servers for ongoing management, service alerting, reporting and remote management with HPE iLO.
Learn more at http://www.hpe.com/info/ilo.
|
|
HPE Server UEFI/Legacy ROM
UEFI enables numerous new capabilities specific to HPE ProLiant servers such as:
· Secure Boot and Secure Start enable for enhanced security
· Operating system specific functionality
· Support for > 2.2 TB (using GPT) boot drives
· USB 3.0 Stack
· Embedded UEFI Shell
· Mass Configuration Deployment Tool using iLO RESTful API that is Redfish API Conformant
· PXE boot support for IPv6 networks
· Workload Profiles for simple performance optimization
UEFI Boot Mode only:
· TPM 2.0 Support
· NVMe Boot Support
· Platform Trust Technology (PTT) can be enabled.
· iSCSI Software Initiator Support.
· HTTP/HTTPs Boot support as a PXE alternative.
· Boot support for option cards that only support a UEFI option ROM
NOTE: For UEFI Boot Mode, boot environment and OS image installations should be configured properly to support UEFI.
NOTE: UEFI FIO Setting (758959-B22) can be selected to configure the system in Legacy mode in the factory for your HPE ProLiant Gen10 Server.
|
|
Intelligent Provisioning
Hassle free server and OS provisioning for one or more servers with Intelligent Provisioning.
Learn more at http://www.hpe.com/servers/intelligentprovisioning.
|
|
iLO RESTful API
iLO RESTful API is Redfish API conformance and offers simplified server management automation such as configuration and maintenance tasks based on modern industry standards. Learn more at http://www.hpe.com/info/restfulapi.
|
|
Server Utilities
Active Health System
The HPE Active Health System (AHS) is an essential component of the iLO management portfolio that provides continuous, proactive health monitoring of HPE servers. Learn more at http://www.hpe.com/servers/ahs.
|
|
Active Health System Viewer
Use the Active Health System Viewer, a web-based portal, to easily read AHS logs and speed problem resolution with HPE self-repair recommendations, to learn more visit: http://www.hpe.com/servers/ahsv.
|
|
Smart Update
Keep your servers up to date with the HPE Smart Update solution by using Smart Update Manager (SUM) to optimize the firmware and driver updates of the Service Pack for ProLiant (SPP). Learn more at https://www.hpe.com/us/en/servers/smart-update.html.
|
|
iLO Amplifier Pack
Designed for large enterprise and service provider environments with hundreds of HPE servers, the iLO Amplifier Pack is a free, downloadable open virtual application (OVA) that delivers the power to discover, inventory and update Gen8, Gen9 and Gen10 HPE servers at unmatched speed and scale. Use with an iLO Advanced License to unlock full capabilities.
Learn more at http://www.hpe.com/servers/iLOamplifierpack.
|
|
HPE iLO Mobile Application
Enables the ability to access, deploy, and manage your server anytime from anywhere from select smartphones and mobile devices. For additional information please visit: http://www.hpe.com/info/ilo/mobileapp.
|
|
RESTful Interface Tool
RESTful Interface tool (iLOREST) is a single scripting tool to provision using iLO RESTful API to discover and deploy servers at scale. Learn more at http://www.hpe.com/info/resttool.
|
|
Scripting Tools
Provision one to many servers using your own scripts to discover and deploy with Scripting Tool (STK) for Windows and Linux or Scripting Tools for Windows PowerShell.
Learn more at http://www.hpe.com/servers/stk and http://www.hpe.com/servers/powershell.
|
|
HPE OneView Standard
HPE OneView Standard can be used for inventory, health monitoring, alerting, and reporting without additional fees. It can monitor multiple HPE server generations. The user interface is similar to the HPE OneView Advanced version, but the software-defined functionality is not available. Learn more at http://www.hpe.com/info/oneview.
|
|
HPE Systems Insight Manager (HPE SIM)
Ideal for environments already using HPE SIM, it allows you to monitor the health of your HPE ProLiant Servers and HPE Integrity Servers. Also provides you with basic support for non-HPE servers. HPE SIM also integrates with Smart Update Manager to provide quick and seamless firmware updates. Learn more at http://www.hpe.com/info/hpesim.
|
|
Warranty
This product is covered by a global limited warranty and supported by HPE Services and a worldwide network of Hewlett Packard Enterprise Authorized Channel Partners resellers. Hardware diagnostic support and repair is available for three years from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HPE Pointnext operational services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
NOTE: Server Warranty includes 3-Year Parts, 3-Year Labor, 3-Year Onsite support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have Hewlett Packard Enterprise replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at:
http://h17007.www1.hpe.com/us/en/enterprise/servers/warranty/.
|